SCALAR OBJECTS

Name	Type	Access	OID	Description

TABLE OBJECTS

Table ipFwAccTable

Table Name	ipFwAccTable
In MIB	UCD-IPFWACC-MIB
Registered at OID	.1.3.6.1.4.1.2021.13.1.1
Table Description	A table with the accounting rules of the IP firewall
Row Description	An accounting rule of the IP firewall

ipFwAccTable Indexes:

Name	Type	Access	Description
1 ipFwAccIndex	INTEGER32 Legal values: 0 .. 2147483647	ReadOnly	Reference index for each firewall rule.

Other ipFwAccTable Columns:

Name	Type	Access	Description
2 ipFwAccSrcAddr	IPADDR	ReadOnly	The source address in the firewall rule.
3 ipFwAccSrcNetMask	IPADDR	ReadOnly	The netmask of the source address in the firewall rule.
4 ipFwAccDstAddr	IPADDR	ReadOnly	The destination address in the firewall rule.
5 ipFwAccDstNetMask	IPADDR	ReadOnly	The netmask of the destination address in the firewall rule.
6 ipFwAccViaName	OCTETSTR Legal Lengths: 1 .. 64 DisplayString	ReadOnly	Note: this object is based on the DisplayString TEXTUAL-CONVENTION. The name of the interface to which the rule applies. If no interface is associated with the present rule, this should contain a dash (-).
7 ipFwAccViaAddr	IPADDR	ReadOnly	The address of the interface to which the rule applies. Using this parameter makes sense when multiple addresses are associated to the same physical interface. If not defined for the current rule this should be set to 0.
8 ipFwAccProto	INTEGER Value Label/Meaning 1 other 2 all 3 tcp 4 udp 5 icmp	ReadOnly	The protocol(s) to which the rule applies.
9 ipFwAccBidir	INTEGER Value Label/Meaning 1 unidirectional 2 bidirectional	ReadOnly	Whether the rule works in both directions (i.e. with the source and destination parts swapped) or not.
10 ipFwAccDir	INTEGER Value Label/Meaning 1 both 2 in 3 out	ReadOnly	Whether the rule applies to packets entering or exiting the kernel.
11 ipFwAccBytes	COUNTER	ReadOnly	The number of bytes that matched this rule since the last reset of the counters.
12 ipFwAccPackets	COUNTER	ReadOnly	The number of packets that matched this rule since the last reset of the counters.
13 ipFwAccNrSrcPorts	INTEGER32	ReadOnly	The number of ports that refer to the source address.
14 ipFwAccNrDstPorts	INTEGER32	ReadOnly	The number of ports that refer to the destination address.
15 ipFwAccSrcIsRange	INTEGER Value Label/Meaning 1 srchasrange 2 srchasnorange	ReadOnly	Interpret the first two ports of the source part as the upper and lower limit of an interval or not.
16 ipFwAccDstIsRange	INTEGER Value Label/Meaning 1 dsthasrange 2 dsthasnorange	ReadOnly	Interpret the first two ports of the destination part as the upper and lower limit of an interval or not.
17 ipFwAccPort1	INTEGER32	ReadOnly	Port number 1.
18 ipFwAccPort2	INTEGER32	ReadOnly	Port number 2.
19 ipFwAccPort3	INTEGER32	ReadOnly	Port number 3.
20 ipFwAccPort4	INTEGER32	ReadOnly	Port number 4.
21 ipFwAccPort5	INTEGER32	ReadOnly	Port number 5.
22 ipFwAccPort6	INTEGER32	ReadOnly	Port number 6.
23 ipFwAccPort7	INTEGER32	ReadOnly	Port number 7.
24 ipFwAccPort8	INTEGER32	ReadOnly	Port number 8.
25 ipFwAccPort9	INTEGER32	ReadOnly	Port number 9.
26 ipFwAccPort10	INTEGER32	ReadOnly	Port number 10.

DEPRECATED OR OBSOLETE OR HISTORIC OBJECTS

NOTIFICATIONS

TEXTUAL CONVENTIONS

These TEXTUAL-CONVENTIONS are used in other parts of the document above. They are SNMP's way of defining a datatype that is used repeatedly by other MIB objects. Any implementation implementing objects that use one of these definitions must follow its DESCRIPTION clause as well as the DESCRIPTION clause of the object itself.

Name	Type	Description
DisplayString	OCTETSTR	Represents textual information taken from the NVT ASCII character set, as defined in pages 4, 10-11 of RFC 854. To summarize RFC 854, the NVT ASCII repertoire specifies: - the use of character codes 0-127 (decimal) - the graphics characters (32-126) are interpreted as US ASCII - NUL, LF, CR, BEL, BS, HT, VT and FF have the special meanings specified in RFC 854 - the other 25 codes have no standard interpretation - the sequence 'CR LF' means newline - the sequence 'CR NUL' means carriage-return - an 'LF' not preceded by a 'CR' means moving to the same column on the next line. - the sequence 'CR x' for any x other than LF or NUL is illegal. (Note that this also means that a string may end with either 'CR LF' or 'CR NUL', but not with CR.) Any object defined using this syntax may not exceed 255 characters in length.

TREE VIEW

Tree view generated by running: snmptranslate -Tp UCD-IPFWACC-MIB::ucdIpFwAccMIB